螺旋风管安装是十分重要的环节，通风、空调工程的主要工作集中在风管的安装上。因此要做好掌握多功能消声管的技术特性，熟悉施工图，了解土建和其它专业工种同本工种的相关情况，核实风管系统的标 高，轴线、预留孔洞，预埋件等是否符合安装条件。备足安装用的各类辅助材料，准备好吊装机具和安装用的其它工具，对风管系统划线定位等工作。

风管的组对：将成品或预制好的风管运至安装地点，结合实际情况进行检查、复核，再按编号进行排列，风管系统的各部分尺寸和角度确认准确无误后，即开始风管组对工作。风管各管段之间的连接采用法兰连接，接口处要求严密不漏风。

一次吊装风管的长度要根据建筑物的条件，风管的壁厚，吊装方法和吊装机具配备情况确定，组对好的风管可把两端的法兰做为基准点，以中间法兰为测点，拉线测量风管的连 接是否平直，偏差大时要进行调整，吊装前，要对风管支、吊架，吊装机具，选用吊装机具的支、吊点，是否正确、牢固进行检查，起吊前要仔细检查，把杆、 滑轮、绳索等是否 固定，绑扎可靠并要清除吊装范围内的各种不安全因素。起吊时，首先要进行试吊，当离地200-300毫米时，停止起升，再一次对吊装机具进行一次全面检查，确认无误后，继续起升到所需高度。把风管固定在支、吊架上之后，才能解开绳索，拆移吊装 机具。

水平干管经找平找正并固定在支、吊架上后，就可进行支管的安装。立管可在水平干管安装前进行安装，支架间距不应大于4米，每根立管固定件不应少于二个。风管水平安装，水平度的允许偏差每米不应大于3毫米，总偏差不应大于20毫米，风管垂 直安装，垂直度的允许偏差每米不应大于2毫米，总偏差不应大于20毫米。